主要成份：多粒径碳化硅颗粒、环氧树脂、增强纤维、Al2O3微粉等。
产品描述：本产品为双组份材料，A组份为主剂，外观为灰色砂浆状；B组份为固化剂，外观为浅黄色液体（或浅黄色膏体）。A、B组份以20：1（或8：1）的重量比混合后常温固化，固化后的材料具有优良的耐磨性能和抗腐蚀性能。
用 途：作为耐磨涂层，适用于管道、槽体、塔壁等设备的磨损修复及耐磨防护，延长设备使用寿命。
特 点：（1）良好的耐磨性和耐腐蚀性；
（2）混合后的材料比较湿软，涂抹效率高，适合快速大面积施工。
（3）冷涂施工，常温固化，操作方便。
Main Components:Multi-grade silicon carbide (SiC) particles, epoxy resin, reinforcing fibers, alumina (Al₂O₃) micropowder, etc.
Product Description: This product is a two-component material. Component A is the main agent, appearing as a gray mortar-like substance; Component B is the curing agent, presenting as a light yellow liquid (or light yellow paste). When mixed at a weight ratio of 20:1 (or 8:1), Components A and B cure at room temperature. The cured material exhibits excellent wear resistance and corrosion resistance.
Application: As a wear-resistant coating, it is suitable for the repair of worn surfaces and wear protection of equipment such as pipelines, tanks, tower walls, etc., extending the service life of the equipment.
Features:
1. Excellent wear resistance and corrosion resistance.
2. The mixed material remains soft and wet, ensuring high application efficiency, making it ideal for rapid large-area construction.
3. Cold application and room-temperature curing, providing convenient operation.
包装规格：
施工步骤：
1、对管道的磨损穿孔部位，在外部先用铁板进行焊补；
2、除去管道内的残余衬胶，或割破衬胶起鼓部位，清理积垢；
3、采用喷砂或打磨的方式，对管道内壁进行粗糙化处理；
4、混合SYZO-33081陶瓷底剂的A和B组份，并施涂在待修复表面；
5、混合SYZO-33097的A和B组份，施涂在陶瓷底剂表面，并压紧拍实抹平；
5、常温固化保养24小时后。
Construction Steps:
1.For the worn or perforated section of the pipeline, first perform external welding repair using an iron plate.
2.Remove the residual rubber lining inside the pipeline or cut open the bulging areas of the lining, then clean out accumulated deposits.
3.Roughen the inner wall of the pipeline using methods such as sandblasting or grinding.
4.Mix components A and B of the SYZO-33081 ceramic primer and apply it to the surface to be repaired.
5.Mix components A and B of SYZO-33097, apply it over the ceramic primer layer, then press firmly and smooth it out.
6.Allow it to cure at room temperature for 24 hours.
安全须知：
• 须在通风良好的环境中进行，必须穿戴工作服、口罩、手套、防护眼镜；
• 施工时应避免皮肤直接接触材料。
Safety Precautions:
•Must be used in a well-ventilated environment.
•Wear protective workwear, a mask, gloves, and safety goggles at all times.
•Avoid direct skin contact with the material during application.
注意事项：
• 建议本产品的施涂厚度在3mm以上。
• 对穿孔或悬空部位的修补，可将混合后的本产品放置15分钟左右，待材料半固化时，填补穿孔部位或悬空处，材料不至于流挂和塌陷。
Precautions:
• The recommended application thickness of this product is 3mm or more.
• For repairing perforations or overhanging areas, allow the mixed product to sit for approximately 15 minutes until it reaches a semi-cured state before filling the perforated or overhanging sections. This prevents the material from sagging or collapsing.